Default Gateway blank Optional; Enter the IP address of the next-hop gateway node if network traffic needs to be able to reach off-subnet destinations. IP Address xxx. Subnet Mask xxx. The default setting selects the command line interface for console access. Default setting recommended unless STP is already running on your network. Optional; The protocol the switch uses to acquire a time signal. The options. The switch Fault LED will be blinking simultaneously. Press the button to step from one view mode to the next.
If it is lit, the port has a link. If the Link LED is blinking, the port has failed its self test. This button is used to reset the switch while it is powered on. This action clears any temporary error conditions that may have occurred and executes the switch self test. It is also used when restoring the switch factory default configuration.
Use this feature if you have misplaced the password and need console access. This button is provided for your convenience, but its presence means that if you are concerned with the security of the switch configuration and operation, you should make sure the switch is installed in a secure location, such as a locked wiring closet.
These LEDs are located on the physical expansion module bulkhead. These LEDs are only viewable in the rear of the ylG product on the expansion slot module itself. FDx and Spd modes have no meaning for the GbE ports on the expansion module. Only the yl and yl switches support a yl module.
The yl module provides 4 ports:. The , yl and yl switches support connectivity to a redundant power supply. This port is used to connect a console to the switch by using the serial cable supplied with the switch.
The console port is located on the front of the , ylG and ylG switches, and on the back of the and ylG switches. The , yl and yl switches do not have a power switch; they are powered on when connected to an active AC power source. These switches automatically adjust to any voltage between volts and either 50 or 60 Hz. There are no voltage range settings required.
Cross-over cables are not required, although they will also work. The pin operation of each port is automatically adjusted for the attached device: if the switch detects that another switch or hub is connected to the port, it configures the port as MDI; if the switch detects that an end-node device is connected to the port, it configures the port as MDI-X. See page. The HP ProCurve , yl and yl switches have the following components shipped with them:.
Switch the Installing. Installing the Switch. Please use the power cord supplied with your product. This power cord is not to be used with other products. Prepare the installation site page Ensure the physical environ-. See page for some installation precautions. Install or remove a yl module optional— page Install or remove a transceiver optional— page If you have. Install or remove mini-GBICs optional — page The switch has. Verify the switch passes self test page Plug the switch into a.
Mount the switch page The Switch can be mounted in a inch. Connect the switch to a power source page Once the switch is. Connect the network cables page Using the appropriate. You may wish to use. Connect a console to the switch optional — page You may wish. At this point, the switch is fully installed. See the rest of this chapter if you need more detailed information on any of these installation steps.
That is, the right or left side of the unit while facing the front. Mount the switch using rail kit part number B21 and shelf kit ABA.
Both kits must be used. Otherwise you will void the warranty. In addition, be sure to use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the switch and power supply. To determine the possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the same circuit as the switch and compare the total with the rating limit for the circuit.
The maximum ampere ratings are usually printed on the devices near the AC power connectors. Cabling Infrastructure - Ensure the cabling infrastructure meets the necessary network specifications. Installation Location - Before installing the switch, plan its location and orientation relative to other devices and equipment:. Insert the module aligning with the guides in the slot. Tighten the captive screws. Refer to the y l Module Installation Guide for more details.
Slide the transceiver in until it stops. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. HP ProCurve , yl and yl Switches. The information contained herein is subject to change without notice. Contents 1 Introducing the Switch Front of the Switches.
Connect a Redundant Power Supply to the switch Optional. A-1 Electrical. A-1 Environmental. A-2 Acoustic. A-2 Safety. B-1 Technology Distance Specifications. B-2 Mode Conditioning Patch Cord. B-4 Installing the Patch Cord. B-6 Other Wiring Rules:. B-8 Cable Diagram. B-9 Cable Diagram. C-2 Hinweise zur Sicherheit. C-3 Considerazioni sulla sicurezza.
C-4 Consideraciones sobre seguridad. C-5 Safety Information Japan. C-6 Safety Information China. C-8 U. C-8 Canada. C-8 Japan. C-8 Korea. C-9 Taiwan. D-1 Index. Introducing the Switch In each of the ylG and ylG switches, one slot is provided in the back of the device to support a four port two fixed CX4 ports and two X2 transceiver ports 10 Gigabit per second Ethernet GbE module.
Table A Introducing the Switch disable it if you do not want to use it. Figure Reset and Clear buttons. The modules provide Introducing either copper or fiber optic media that conforms to the Gigabit Ethernet standard as well as dual 10 gigabit copper or uplink ports.
The switches do not support a module slot. Fault Off The normal state; indicates there are no fault conditions on the switch. The Status LED for the component with the fault will blink simultaneously. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch. Continue to press the Clear button while releasing the Reset button. The switch will then complete its self test and begin operating with its configuration restored to the factory default settings.
To restore the factory default configuration using the console, execute the erase startup-config command from the console command prompt. Download pages , 9.
0コメント